|
◆★◆【北京冠測精電儀器設備有限公司】產品系列--------聚乙烯壓痕硬度儀◆★◆ 聚乙烯壓痕硬度儀,全自動聚乙烯壓痕硬度儀,全自動聚乙烯壓痕硬度測定儀,聚乙烯防腐層壓痕硬度測定儀,聚乙烯壓痕硬度儀, --------------------------------------------------------------------------------
◆★◆★◆**北京冠測精電儀器設備有限公司**◆★◆★◆ 地址:北京昌平科技園區涼水河路1號院2號樓創意大廈 網址:http:// *域名隱藏* Email: guanceyq@ *域名隱藏* 電話:010-57223836 57223837 57223838 57223839
冠測公司以精美的產品、精湛的技術、精良的品質、精心的服務贏得了廣大用戶的一致認可。 冠測公司***所供產品均為經過標準化生產,嚴格測試并檢驗合格后才出廠的,性能卓越。 ◆★◆★◆**產品名稱**◆★◆★◆ 聚乙烯壓痕硬度儀 全自動聚乙烯壓痕硬度儀 全自動聚乙烯壓痕硬度測定儀 聚乙烯防腐層壓痕硬度測定儀 滿足標準: GB/T 23257-2009 埋地鋼質管道聚乙烯防腐層 SY/T0413-2002《埋地鋼質管道聚乙烯防腐技術標準》-壓痕硬度測定方法 產品概述: Product overview: 全自動壓痕硬度儀主要應用于在一定的恒溫條件下,用直徑為1.8mm或截面積為2.5mm2的壓頭對試樣施加一定的恒負荷壓力,并保持24小時后,檢測試樣的抗壓能力,即通過壓針壓入到試樣的深度來表示。。 Automatic indentation hardness tester is mainly used in a certain temperature conditions, with a diameter of 1.8 mm or cross-sectional area 2.5mm l pressure head of samples applied to certain constant load pressure, and was maintained for 24 hours after, the compressive strength of the test specimens, that is, through the needle pressing pressure into the depth of sample to represent.
產品特點: Product features: 1、 本儀器核心控制部分通過7寸觸摸屏設置參數并控制。 1, the core control of the instrument through the 7 Inch Touch screen set parameters and control. 2、 本儀器變形采集利用國內***的微型位移傳感器技術,***小位移采集精度為:0.001MM 2, the instrument deformation acquisition and use of the leading micro displacement sensor technology, the minimum displacement acquisition accuracy: 0.001MM 3、 設置好參數后,點開始實驗后自動加載,實驗結束后自動計算結果,同時壓頭自動復位到初始位置進行下次實驗 3, set the parameters after the start of the experiment, automatic loading, automatic calculation results after the end of the experiment, while the head automatically reset to the initial position for the next experiment 4、 本儀器帶有微型打印機,可以對試驗結果進行打印。 4, the instrument with a micro printer, you can print the results of the test. 5、 恒溫槽底部有放液孔,方便更換加熱介質。
5, the bottom of the constant temperature tank has a liquid discharging hole, which is convenient for replacing the heating medium. 設備主要組成部分及技術要求: Main components and technical requirements of equipment: 1、主機、溫控系統、砝碼及自動加載裝置、位移檢測系統、控制系統等。 1, host, temperature control system, weight and automatic loading device, displacement detection system, control system, etc.. 2、試驗工位:3個。 2, test station: 3. 3、溫控系統: 3, temperature control system: 恒溫范圍:0~200℃。 Constant temperature range: 0~200. 控溫精度:±0.1℃。 Temperature control accuracy: + 0.1. 控溫方式:具備加熱、制冷及恒溫功能,采用手動開啟或停止。 Temperature control method: with heating, cooling and constant temperature function, the use of manual open or stop. 制冷方式:內置制冷機可實現自動制冷。
Refrigeration mode: built-in refrigerator can realize automatic refrigeration. 溫度顯示:控制屏液晶顯示。 Temperature display: LCD display control panel. 升溫速率:室溫至200℃,60min。 Heating rate: room temperature to 200 degrees C, 60min. 降溫速率:室溫至0℃,30min。 Cooling rate: room temperature to 0 degrees C, 30min. 4、試驗載荷: 4, test load: 載荷:3套,每套由壓桿、砝碼與位移傳感器探頭組成,總質量2500g。 Load: 3 sets, each set by the pressure bar, weight and displacement sensor probe, the total quality of 2500g. 壓桿:由砝碼盤、連接桿和壓針組成,總質量不超過250g,壓針直徑Φ1.8mm或截面積2.5mm2。 Bar: by the weight plate, a connecting rod and a pressure needle, the total mass of not more than 250g, needle diameter 1.8mm or cross-sectional area 2.5mm2. 砝碼:質量2250g。 Weight: quality 2250g. -------------------------------------------------------------------------------- ◆★◆【易促寶】---品牌策劃、全網營銷! ◆★◆
http:// *域名隱藏* /guanggao/xinxi2_ *域名隱藏* http:// *域名隱藏* / *域名隱藏* http:// *域名隱藏* /c2902/ *域名隱藏* ---------------------------------------------------------------------- 聚乙烯防腐層壓痕硬度測定儀,聚乙烯壓痕硬度儀,全自動聚乙烯壓痕硬度測定儀,聚乙烯壓痕硬度儀,全自動聚乙烯壓痕硬度儀,全自動聚乙烯壓痕硬度測定儀,
規格: |
冠測 |
數量: |
1000 |
包裝:精裝 |
日期: |
2016-03-10 |
|
|